+7 (953) 49 555 44
info@laserbiz.ru
Заказать звонок

back to generator Catalog

SmallPartsTray2

A Type Tray variant with slopes toward the front

Assemble inside out. If there are inner front to back walls start with attaching the floor boards to them. Then add the vertical inner left to right walls. After sliding in the slopes attach the outer wall to fix everything in place. If there are no inner front to back walls just add everything to one side wall and then add the other one after that. Possibly saving the front and back as last step.

Viewed:

Layouts generated:

Settings for Finger Joints

angle

style

style of the fingers

surroundingspaces

space at the start and end in multiple of normal spaces

bottom_lip

height of the bottom lips sticking out (multiples of thickness) FingerHoleEdge only!

edge_width

space below holes of FingerHoleEdge (multiples of thickness)

extra_length

extra material to grind away burn marks (multiples of thickness)

finger

width of the fingers (multiples of thickness)

play

extra space to allow finger move in and out (multiples of thickness)

space

space between fingers (multiples of thickness)

width

width of finger holes (multiples of thickness)

Settings for Stackable Edges

angle

inside angle of the feet

bottom_stabilizers

height of strips to be glued to the inside of bottom edges (multiples of thickness)

height

height of the feet (multiples of thickness)

holedistance

distance from finger holes to bottom edge (multiples of thickness)

width

width of the feet (multiples of thickness)

Settings for Hinges and HingePins

grip_percentage

outset

have lid overlap at the sides (similar to OutSetEdge)

pinwidth

set to lower value to get disks surrounding the pins

style

"outset" or "flush"

axle

diameter of the pin hole (multiples of thickness)

grip_length

fixed length of the grips on he lids (multiples of thickness)

hingestrength

thickness of the arc holding the pin in place (multiples of thickness)

Settings for Cabinet Hinges

bore

diameter of the pin hole in mm

eyes_per_hinge

pieces per hinge

hinges

number of hinges per edge

style

style of hinge used

eye

radius of the eye (multiples of thickness)

play

space between eyes (multiples of thickness)

spacing

minimum space around the hinge (multiples of thickness)

Settings for Slide-on Lids

angle

hole_width

width of the "finger hole" in mm

second_pin

additional pin for better positioning

spring

position(s) of the extra locking springs in the lid

style

style of the fingers

surroundingspaces

space at the start and end in multiple of normal spaces

bottom_lip

height of the bottom lips sticking out (multiples of thickness) FingerHoleEdge only!

edge_width

space below holes of FingerHoleEdge (multiples of thickness)

extra_length

extra material to grind away burn marks (multiples of thickness)

finger

width of the fingers (multiples of thickness)

play

extra space to allow finger move in and out (multiples of thickness)

space

space between fingers (multiples of thickness)

width

width of finger holes (multiples of thickness)

Settings for Click-on Lids

angle

angle of the hooks bending outward

bottom_radius

radius at the bottom (multiples of thickness)

depth

length of the hooks (multiples of thickness)

Settings for RoundedTriangleEdge

height

height above the wall

r_hole

radius of hole

radius

radius of top corner

outset

extend the triangle along the length of the edge (multiples of thickness)

Settings for Mounting Edge

d_head

head diameter of mounting screw in mm

d_shaft

shaft diameter of mounting screw in mm

margin

minimum space left and right without holes (fraction of the edge length)

num

number of mounting holes (integer)

side

side of box (not all valid configurations make sense...)

style

edge style

Settings for HandleEdge

height

height above the wall in mm

hole_height

height of hole(s) in percentage of maximum hole height (handle height - 2 * material thickness)

hole_width

width of hole(s) in percentage of maximum hole width (width of edge - (n+1) * material thickness)

on_sides

added to side panels if checked, to front and back otherwise (only used with top_edge parameter)

radius

radius of corners in mm

outset

extend the handle along the length of the edge (multiples of thickness)

Settings for the Lid

handle

style

type of lid to create

handle_height

height of the handle (if applicable)

height

height of the brim (if any)

play

play when sliding the lid on (if applicable)

Main Settings

inner height in mm (unless outside selected)

sections left to right in mm

sections back to front in mm

inner height of inner walls in mm (unless outside selected)(leave to zero for same as outer walls)

outside

treat sizes as outside measurements

back_height

additional height of the back wall - e top edge only

radius

radius for strengthening side walls with back_height

handle

add handle to the bottom (changes bottom edge in the front)

Default Settings

thickness

thickness of the material in mm

format

format of resulting file

tabs

width of tabs holding the parts in place in mm (not supported everywhere)

qr_code

Add a QR Code with link or command line to the generated output

debug

print surrounding boxes for some structures

labels

label the parts (where available)

reference

print reference rectangle with given length in mm (zero to disable)

inner_corners

style for inner corners

burn

burn correction in mm (bigger values for tighter fit)